Electronics Design Engineer-1 (Basic)
Electronics Design Engineer-1 (Basic)
Time:00:30:00
Est. Time: 00:30:00
Max Points: 60
Max Points: 60
This will submit your entire assessment.
Electronics Design Engineer-1 (Basic)
60
Max Points
All Problems (30)
QUESTIONS
30 QuestionsResistor Power Rating Risk-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify Carbon Film Resistor (CFR)-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Decode SMD Resistor Marking-m
Hardware Design- Component Skills•2 pts•Est: 1 min
High-Speed Digital IC Decoupling-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify Lead- SMD Electrolytic Capacitor-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Overvoltage to Capacitor-m
Hardware Design- Component Skills•2 pts•Est: 1 min
EMI Suppression-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Inductor Selection-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Noise Filtering-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify the Highlighted Component-IV-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify Component-I-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify the Highlighted Component-VII-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify diode Purpose-I-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify the Risky Replacement-III-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Reset Push Button-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Key Lock Switch-m
Hardware Design- Component Skills•2 pts•Est: 1 min
NO–NC–COM Relay Contacts-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Relay Selection-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Relay Selection with Safety Margin-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Optocoupler Replacement-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Optocoupler Output Type-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Compliance & Qualification Selection-m
Hardware Design- Component Skills•2 pts•Est: 1 min
BJT Base–Emitter Short-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Power Budgeting for LEDs-m
Hardware Design- Component Skills•2 pts•Est: 1 min
Identify the SMD LED ii-m
Hardware Design- Component Skills•2 pts•Est: 1 min
AC Input Component-m
Hardware Design -Circuit Protection•2 pts•Est: 1 min
PPTC Identification-m
Hardware Design -Circuit Protection•2 pts•Est: 1 min
TVS Power Rating-m
Hardware Design -Circuit Protection•2 pts•Est: 1 min
GDT Schematic Symbol-m
Hardware Design -Circuit Protection•2 pts•Est: 1 min
NTC Selection for SMPS-m
Hardware Design -Circuit Protection•2 pts•Est: 1 min
Welcome To
Electronics Design Engineer-1 (Basic)
A practical mock test for engineers working with electronic components in circuit design. Designed to help you prepare for job roles in electronics.
Duration
30min
Problems
30
Organization
Mock Test
Sponsored By
Skills
Your assessment contains the following skills.
| Number | Skills | Problems |
|---|---|---|
| 1 | Hardware Design- Component Skills | 25 Questions |
| 2 | Hardware Design -Circuit Protection | 5 Questions |
Section 1
Hardware Design- Component Skills
25 Questions
Section 2
Hardware Design -Circuit Protection
5 Questions
Instructions
Read the instructions carefully before starting.
- This is a standard practice test; your result will remain private.
- Please keep 30 minutes available and attempt the test without interruption.
- Tab switching is not allowed.
- Use a laptop or desktop for the best experience.
- Complete the test in one sitting.
- Use a stable internet connection and avoid refreshing or closing the page during the test.